Operation winter coat - fabric prep

As I had some lovely (and more expensive than usual) fabrics for this coat, I wanted to treat them right. Since I asked for a lot of advice and googled a fair bit, I thought my findings might be useful to others.

Starting with the outer fabric which is a wool blend - 90% wool, 10% poly. This is a good combination for me as I am sensitive to 100% wool  A lot of people can get away with wool in a coat as it doesn't sit against the skin but I particularly dislike it against my neck and this coat has a collar so wool blend it was. 

After a lot of googling I found 3 main methods for pre shrinking wool. First is taking to the dry cleaners.  Easy but pricy so not for me. Second is steaming with the iron (as Tasia did here). Simple but time consuming. Thirdly is this method outlined by Pam from Off the Cuff (this is a link to her new blog but her old one here is a treasure trove of tips, especially for shirtmaking).  To save you a click, you wet large towels with hot water and put in the tumble dryer with your dry yardage. That's it!

I was concerned about trying this with my whole yardage so I tumble dried a swatch first for the recommended 40 minutes.  There was no obvious change to the look of the fabric so I put the whole yardage in the dryer with 2 damp (wrung out as much as possible) bath towels. It worked perfectly - but if you do this be careful taking it out of the machine as it was still boiling hot! A quick press later and my wool was ready to go.

The lining is viscose acetate.  I had planned to wash as normal but when the fabric arrived it had a dry clean only sticker on the tissue it was wrapped in. I considered not prewashing as I plan to dryclean the finished garment but advice from the lovely Claire Louise from the Thrifty Stitcher that it's really important to pre wash linings as even a bit of sweat can cause shrinkage.  So I decided to put in in a delicate wash and it came out fine. Another great tip from Claire Louise was to iron it damp to get the creases out properly. This worked brilliantly and not sure why I haven't tried it before!

This just left the interfacing. I ordered Speed Tailoring from Gill Arnold on the advice of Anne from Mercury Handmade and it came with really detailed instructions on how to pre shrink,  which I have never done with fusible interfacing before. I soaked it in hand hot water for 20 minutes, rolled it up in a towel to take out excess water and hung up to dry. When applying, Gill recommends a steam shrink, where you place the interfacing on top of the fabric and steam from a couple of inches away, smooth out fabric and interfacing and then press using a press cloth to adhere.  This method worked really well and the interfacing is really lovely stuff.  It stabilises without stiffening and adhered perfectly and easily to the fabric.

Hopefully some of these tips might help if you are making a coat in future!

Operation winter coat - the reveal!

So here is my final coat!

I am so happy with it and it's an absolute pleasure to put it on every day. Of course the cost/effort per wear on a coat comes out pretty well which is satisfying! 

In this post, I'm showing off the final pics and will talk about fitting adjustments I made, and I'll show you details in another post. 

On comparing my actual measurements to my pattern measurements, I found I needed an FBA (no surprise), a little extra room at the hips/ bum level (another non - surprise) and more ease in the arms (I appear to have weirdly big elbows!). I also added 1/2" shoulder width and did a small square shoulder adjustment.

The front pattern piece was tough to adjust as it looked like this:

On the advice of lovely Brooke from Custom Style I had planned to cut it apart at the waist, but as I needed extra room at the hips too I was able to slash the pattern piece all the way down and add in some extra in the right places.

Should have taken my hands out of my pockets to photograph the back - that pulling isn't there without them!

The weirdest thing is that I did no length adjustments in the body at all! The waist was in the right place and the hem length was perfect.  In hindsight, the pockets could stand to be perhaps 1.5" lower  as it feels like I pull on them slightly when I put my hands in. But they are totally functional.  I also lengthened the sleeves to full length from bracelet length and as a result had to taper them slightly.

I muslined one sleeve and also the collar piece as I was concerned it looked a bit small in the picture (it's fine). However I decided to add darts to the back to take out some excess fabric at back waist. This was done by pinching out the right amount of fabric at waist level, splitting that between 2 darts and measuring where I wanted them to end top and bottom. I had a bit of trial and error in the dart positioning at first as I placed them too close to the side seams so I was glad I had just pinned them to begin with. Me and the seam ripper are too friendly as it is!  

In the final fabric I ended up taking in the side seams more to narrow the bodice to the waist as the shape as drafted  just wasn't working for me. Unfortunately I feel like I took a lot of the vintage flavour out of the coat, but it definitely works better for me this way. 

Details of the construction to follow! 

One last pic as it's a nice background!

Operation winter coat is go!

I may not have been blogging too much due to work and general life busy-ness, but I have been sewing and planning quite a bit!

The big project I am working on is a winter coat.

I was looking for a fairly simple shape with a collar and some waist shaping and I picked up this great 1960s pattern on Etsy:

It has lovely princess seams running to the waist with welt pockets at the bottom, bound buttonholes and is fully lined.

I knew I was going to have to buy fabric online for it as my local fabric shop just doesn't stock great quality coating. The fabric I used for my Anise really hasn't held up well which is frustrating when you think of all the work that goes into a coat (especially one with welt pockets and bound buttonholes!). After much perusing of online fabric shops (it's a dirty job...) I ordered a stack of swatches from Stone Fabrics. They have a great selection of coatings and I have read good things about their quality. You have to call up and order but they were very helpful and got my order out really quickly - they're not paying me to recommend them BTW, I just like to give praise where it's due!

I ordered this wool mix coating (90% wool but not scratchy - 100% wool rarely works on my skin). A good tip I found was to keep rubbing the swatches together over a few days to see how they might hold up to wear. I actually rejected my original choice after it went a bit fluffy when I did this so hopefully I have chosen one that will wear well!

The lining is also from Stone Fabrics and it's viscose acetate in a beautiful peacock blue - the picture really does not do the colour justice.

As ever, I asked for advice on twitter for interfacing and the ever helpful Anne from Mercury Handmade recommended Speed Tailoring from Gill Arnold as she uses it in all her coats. This stuff is ideal for stabilising an open weave and is beautifully soft.

For buttons, I bought huge 1960s style ones from John  Lewis. I hope they don't look stupidly big on as I'll have to do the bound buttonholes first!

I think you'll be getting quite a lot of in progress posts on this as coats take such a long time. Wish me luck!